The BaitShop Homepage
Forum Home Forum Home > FireArms, et cetera > Bowhunting and Archery
  New Posts New Posts RSS Feed - target tips
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

This site is completely supported by donations; there are no corporate sponsors. We would be honoured if you would consider a small donation, to be used exclusively for forum expenses.



Thank you, from the BaitShop Boyz!

target tips

 Post Reply Post Reply
Author
Message
stinky View Drop Down
.243 Winchester
.243 Winchester


Joined: 30 August 2007
Location: United States
Status: Offline
Points: 214
Post Options Post Options   Thanks (0) Thanks(0)   Quote stinky Quote  Post ReplyReply Direct Link To This Post Topic: target tips
    Posted: 14 April 2014 at 17:35
My kid has just started shooting archery in 4H.  Today, I buy new arrows and then glue the tips on, at about 4p.  At about 6p, the tips were coming off at the range....as a side note, when I got home, I grabbed the remaining ones, and pulled em all out w/pliers and the glue was still wet (maybe the main problem).

One of the instructors noted that my tips have a mushroom bulge on them, just above the base (the bulge is maybe a 1/16" total, but probably half of that).  He recommended getting tips that are the same size as the base as they are theoretically easier to pull out. 

What do you think?
John 14:6
Back to Top
d4570 View Drop Down
.416 Rigby
.416 Rigby
Avatar

Joined: 27 January 2004
Location: United States
Status: Offline
Points: 9403
Post Options Post Options   Thanks (0) Thanks(0)   Quote d4570 Quote  Post ReplyReply Direct Link To This Post Posted: 15 April 2014 at 01:24
??????? sorry
Remember: Four boxes keep us free ,the soap box, the ballot box, the jury box, AND the cartridge box
Back to Top
BEAR View Drop Down
Administrator
Administrator
Avatar

Joined: 07 September 2013
Location: Appalachian Mtn
Status: Offline
Points: 13734
Post Options Post Options   Thanks (0) Thanks(0)   Quote BEAR Quote  Post ReplyReply Direct Link To This Post Posted: 15 April 2014 at 02:02

4p-6p   ???????  is this an afternoon project?

what are they  rubber tipped?

Back to Top
stinky View Drop Down
.243 Winchester
.243 Winchester


Joined: 30 August 2007
Location: United States
Status: Offline
Points: 214
Post Options Post Options   Thanks (0) Thanks(0)   Quote stinky Quote  Post ReplyReply Direct Link To This Post Posted: 16 April 2014 at 17:48
I mis-spoke.  I didn't glue the tips in, I glued the inserts in.

Here are the tips.

http://goldtip.com/pointsdetail.aspx?nid=44


Edited by stinky
John 14:6
Back to Top
BEAR View Drop Down
Administrator
Administrator
Avatar

Joined: 07 September 2013
Location: Appalachian Mtn
Status: Offline
Points: 13734
Post Options Post Options   Thanks (0) Thanks(0)   Quote BEAR Quote  Post ReplyReply Direct Link To This Post Posted: 17 April 2014 at 02:19

Ok I got it now.  You  have plastic threaded inserts into your aluminum or carbon hollow shafts.  Then you have threaded points, filed points.

I've never used the Bulging" points.  My guess is that because they are over sized they do not penetrate far and could be easier to pull out.

On foam targets the foam spreads and lets the arrow slid in, the friction on the shaft sometimes creats a heat bond, and arrows can be difficult to impossible to remove on heavy powered bows.

the bulge points, should have a reverse taper from front to back so that the back is flush with the outside diameter of the shaft and tapers up to the large diameter front of the point, creating a flush fit af the shaft with the rear of the point.   If the rear of the point is larger than the arrow shaft, then the tip acts as a bard and holds you point in the materail, so tight that the insert and the point pull out of the shaft.

I'm not sure what the targets are made of?  Some materials like plastic foam actually grab the point and the bulge could make it difficult to pull the point out (without pulling the insert out also).

I think I'd just use regular target points (without the bulge.  the points should be the same size as the outside dimension of your shaft to avoid it acting like a bulge again.  Some people use a lube on the shaft and point when shooting into foam.

 



Edited by BEAR
Back to Top
RobertMT View Drop Down
.416 Rigby
.416 Rigby
Avatar

Joined: 12 March 2008
Location: United States
Status: Offline
Points: 4413
Post Options Post Options   Thanks (0) Thanks(0)   Quote RobertMT Quote  Post ReplyReply Direct Link To This Post Posted: 17 April 2014 at 05:10
They make arrow pullers, but a piece of foam pipe insulation, works as well.  You'll bend far less aluminum arrows.  As far as the tips, I used to use hot glue, it's fast and easy.  I epoxied them in once, not the best idea.
Want to stop Drunk Drivers, from Killing Sober Drivers? Ban Sober Drivers from Driving. That's how Gun Control Works.

NRA Benefactor Life, GOA Patriot, SAF   

Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.